Games of Daze

home *** CD-ROM | disk | FTP | other *** search

/ Games of Daze / Infomagic - Games of Daze (Summer 1995) (Disc 1 of 2).iso / x2ftp / msdos / formats / riffwave / riff.fmt < prev

Wrap

Text File | 1992-05-19 | 27.1 KB | 776 lines

RIFF WAVE (.WAV) file format ---------------------------- From: Rob Ryan <ST802200@brownvm.brown.edu> Organization: Brown University I found the following lengthy excerpt in a document rmrtf.zrt (it is actually a .zip file) in the vendor/microsoft/multimedia subdirectory at the ftp.uu.net ftp site. It is presumably beyond the scope (in terms of the amount of detail) of your document, but nevertheless, I thought that it may help you in including references to the Windows .WAV format in the future. Let me know if you have any questions/comments. Again, thank you for your helpful summary. Keep it up! The following is taken from RIFFMCI.RTF, "Multimedia Programming Interface and Data Specification v1.0", a Windows RTF (Rich Text Format) file contained in the .zip file, RMRTF.ZRT. The original document is quite long and this constitutes pages 83-95 of the text format version (starting on roughly page 58 of the RTF version). If you would like a PostScript version, let me know and I can make one up for you. Waveform Audio File Format (WAVE) This section describes the Waveform format, which is used to represent digitized sound. The WAVE form is defined as follows. Programs must expect (and ignore) any unknown chunks encountered, as with all RIFF forms. However, <fmt-ck> must always occur before <wave-data>, and both of these chunks are mandatory in a WAVE file. <WAVE-form> -> RIFF( 'WAVE' <fmt-ck> // Format [<fact-ck>] // Fact chunk [<cue-ck>] // Cue points [<playlist-ck>] // Playlist [<assoc-data-list>] // Associated data list <wave-data> ) // Wave data The WAVE chunks are described in the following sections. WAVE Format Chunk The WAVE format chunk <fmt-ck> specifies the format of the <wave-data>. The <fmt-ck> is defined as follows: <fmt-ck> -> fmt( <common-fields> <format-specific-fields> ) <common-fields> -> struct { WORD wFormatTag; // Format category WORD wChannels; // Number of channels DWORDdwSamplesPerSec; // Sampling rate DWORDdwAvgBytesPerSec; // For buffer estimation WORD wBlockAlign; // Data block size } The fields in the <common-fields> chunk are as follows: Field Description wFormatTag A number indicating the WAVE format category of the file. The content of the <format-specific-fields> portion of the `fmt' chunk, and the interpretation of the waveform data, depend on this value. You must register any new WAVE format categories. See ``Registering Multimedia Formats'' in Chapter 1, ``Overview of Multimedia Specifications,'' for information on registering WAVE format categories. ``Wave Format Categories,'' following this section, lists the currently defined WAVE format categories. wChannels The number of channels represented in the waveform data, such as 1 for mono or 2 for stereo. dwSamplesPerSe The sampling rate (in samples per c second) at which each channel should be played. dwAvgBytesPerS The average number of bytes per second ec at which the waveform data should be transferred. Playback software can estimate the buffer size using this value. wBlockAlign The block alignment (in bytes) of the waveform data. Playback software needs to process a multiple of wBlockAlign bytes of data at a time, so the value of wBlockAlign can be used for buffer alignment. The <format-specific-fields> consists of zero or more bytes of parameters. Which parameters occur depends on the WAVE format category-see the following section for details. Playback software should be written to allow for (and ignore) any unknown <format-specific-fields> parameters that occur at the end of this field. WAVE Format Categories The format category of a WAVE file is specified by the value of the wFormatTag field of the `fmt' chunk. The representation of data in <wave-data>, and the content of the <format-specific-fields> of the `fmt' chunk, depend on the format category. The currently defined open non-proprietary WAVE format categories are as follows: wFormatTag Value Format Category WAVE_FORMAT_PCM (0x0001) Microsoft Pulse Code Modulation (PCM) format The following are the registered proprietary WAVE format categories: wFormatTag Value Format Category IBM_FORMAT_MULAW IBM mu-law format (0x0101) IBM_FORMAT_ALAW (0x0102) IBM a-law format IBM_FORMAT_ADPCM IBM AVC Adaptive (0x0103) Differential Pulse Code Modulation format The following sections describe the Microsoft WAVE_FORMAT_PCM format. Pulse Code Modulation (PCM) Format If the wFormatTag field of the <fmt-ck> is set to WAVE_FORMAT_PCM, then the waveform data consists of samples represented in pulse code modulation (PCM) format. For PCM waveform data, the <format-specific-fields> is defined as follows: <PCM-format-specific> -> struct { WORD wBitsPerSample; // Sample size } The wBitsPerSample field specifies the number of bits of data used to represent each sample of each channel. If there are multiple channels, the sample size is the same for each channel. For PCM data, the wAvgBytesPerSec field of the `fmt' chunk should be equal to the following formula rounded up to the next whole number: wBitsPerSample wChannels x wBitsPerSecond x -------------- 8 The wBlockAlign field should be equal to the following formula, rounded to the next whole number: wBitsPerSample wChannels x -------------- 8 Data Packing for PCM WAVE Files In a single-channel WAVE file, samples are stored consecutively. For stereo WAVE files, channel 0 represents the left channel, and channel 1 represents the right channel. The speaker position mapping for more than two channels is currently undefined. In multiple-channel WAVE files, samples are interleaved. The following diagrams show the data packing for a 8-bit mono and stereo WAVE files: Sample 1 Sample 2 Sample 3 Sample 4 Channel 0 Channel 0 Channel 0 Channel 0 Data Packing for 8-Bit Mono PCM Sample 1 Sample 2 Channel 0 Channel 1 Channel 0 Channel 0 (left) (right) (left) (right) Data Packing for 8-Bit Stereo PCM The following diagrams show the data packing for 16-bit mono and stereo WAVE files: Sample 1 Sample 2 Channel 0 Channel 0 Channel 0 Channel 0 low-order high-order low-order high-order byte byte byte byte Data Packing for 16-Bit Mono PCM Sample 1 Channel 0 Channel 0 Channel 1 Channel 1 (left) (left) (right) (right) low-order high-order low-order high-order byte byte byte byte Data Packing for 16-Bit Stereo PCM Data Format of the Samples Each sample is contained in an integer i. The size of i is the smallest number of bytes required to contain the specified sample size. The least significant byte is stored first. The bits that represent the sample amplitude are stored in the most significant bits of i, and the remaining bits are set to zero. For example, if the sample size (recorded in nBitsPerSample) is 12 bits, then each sample is stored in a two-byte integer. The least significant four bits of the first (least significant) byte is set to zero. The data format and maximum and minimums values for PCM waveform samples of various sizes are as follows: Sample Size Data Format Maximum Value Minimum Value One to Unsigned 255 (0xFF) 0 eight bits integer Nine or Signed Largest Most negative more bits integer i positive value of i value of i For example, the maximum, minimum, and midpoint values for 8-bit and 16-bit PCM waveform data are as follows: Format Maximum Minimum Value Midpoint Value Value 8-bit PCM 255 (0xFF) 0 128 (0x80) 16-bit PCM 32767 -32768 0 (0x7FFF) (-0x8000) Examples of PCM WAVE Files Example of a PCM WAVE file with 11.025 kHz sampling rate, mono, 8 bits per sample: RIFF( 'WAVE' fmt(1, 1, 11025, 11025, 1, 8) data( <wave-data> ) ) Example of a PCM WAVE file with 22.05 kHz sampling rate, stereo, 8 bits per sample: RIFF( 'WAVE' fmt(1, 2, 22050, 44100, 2, 8) data( <wave-data> ) ) Example of a PCM WAVE file with 44.1 kHz sampling rate, mono, 20 bits per sample: RIFF( 'WAVE' INFO(INAM("O Canada"Z)) fmt(1, 1, 44100, 132300, 3, 20) data( <wave-data> ) ) Storage of WAVE Data The <wave-data> contains the waveform data. It is defined as follows: <wave-data> -> { <data-ck> : <data-list> } <data-ck> -> data( <wave-data> ) <wave-list> -> LIST( 'wavl' { <data-ck> : // Wave samples <silence-ck> }... ) // Silence <silence-ck> -> slnt( <dwSamples:DWORD> ) // Count of // silent samples Note: The `slnt' chunk represents silence, not necessarily a repeated zero volume or baseline sample. In 16-bit PCM data, if the last sample value played before the silence section is a 10000, then if data is still output to the D to A converter, it must maintain the 10000 value. If a zero value is used, a click may be heard at the start and end of the silence section. If play begins at a silence section, then a zero value might be used since no other information is available. A click might be created if the data following the silent section starts with a nonzero value. FACT Chunk The <fact-ck> fact chunk stores important information about the contents of the WAVE file. This chunk is defined as follows: <fact-ck> -> fact( <dwFileSize:DWORD> ) // Number of samples The `fact'' chunk is required if the waveform data is contained in a `wavl'' LIST chunk and for all compressed audio formats. The chunk is not required for PCM files using the `data'' chunk format. The "fact" chunk will be expanded to include any other information required by future WAVE formats. Added fields will appear following the <dwFileSize> field. Applications can use the chunk size field to determine which fields are present. Cue-Points Chunk The <cue-ck> cue-points chunk identifies a series of positions in the waveform data stream. The <cue-ck> is defined as follows: <cue-ck> -> cue( <dwCuePoints:DWORD> // Count of cue points <cue-point>... ) // Cue-point table <cue-point> -> struct { DWORD dwName; DWORD dwPosition; FOURCC fccChunk; DWORD dwChunkStart; DWORD dwBlockStart; DWORD dwSampleOffset; } The <cue-point> fields are as follows: Field Description dwName Specifies the cue point name. Each <cue-point> record must have a unique dwName field. dwPosition Specifies the sample position of the cue point. This is the sequential sample number within the play order. See ``Playlist Chunk,'' later in this document, for a discussion of the play order. fccChunk Specifies the name or chunk ID of the chunk containing the cue point. dwChunkStart Specifies the file position of the start of the chunk containing the cue point. This is a byte offset relative to the start of the data section of the `wavl' LIST chunk. dwBlockStart Specifies the file position of the start of the block containing the position. This is a byte offset relative to the start of the data section of the `wavl' LIST chunk. dwSampleOffset Specifies the sample offset of the cue point relative to the start of the block. Examples of File Position Values The following table describes the <cue-point> field values for a WAVE file containing multiple `data' and `slnt' chunks enclosed in a `wavl' LIST chunk: Cue Point Field Value Location In a `slnt' fccChunk FOURCC value `slnt'. chunk dwChunkStart File position of the `slnt' chunk relative to the start of the data section in the `wavl' LIST chunk. dwBlockStart File position of the data section of the `slnt' chunk relative to the start of the data section of the `wavl' LIST chunk. dwSampleOffs Sample position of the cue et point relative to the start of the `slnt' chunk. In a PCM fccChunk FOURCC value `data'. `data' chunk dwChunkStart File position of the `data' chunk relative to the start of the data section in the `wavl' LIST chunk. dwBlockStart File position of the cue point relative to the start of the data section of the `wavl' LIST chunk. dwSampleOffs Zero value. et In a fccChunk FOURCC value `data'. compressed `data' chunk dwChunkStart File position of the start of the `data' chunk relative to the start of the data section of the `wavl' LIST chunk. dwBlockStart File position of the enclosing block relative to the start of the data section of the `wavl' LIST chunk. The software can begin the decompression at this point. dwSampleOffs Sample position of the cue et point relative to the start of the block. The following table describes the <cue-point> field values for a WAVE file containing a single `data' chunk: Cue Point Field Value Location Within PCM fccChunk FOURCC value `data'. data dwChunkStart Zero value. dwBlockStart Zero value. dwSampleOffs Sample position of the cue et point relative to the start of the `data' chunk. In a fccChunk FOURCC value `data'. compressed `data' chunk dwChunkStart Zero value. dwBlockStart File position of the enclosing block relative to the start of the `data' chunk. The software can begin the decompression at this point. dwSampleOffs Sample position of the cue et point relative to the start of the block. Playlist Chunk The <playlist-ck> playlist chunk specifies a play order for a series of cue points. The <playlist-ck> is defined as follows: <playlist-ck> -> plst( <dwSegments:DWORD> // Count of play segments <play-segment>... ) // Play-segment table <play-segment> -> struct { DWORD dwName; DWORD dwLength; DWORD dwLoops; } The <play-segment> fields are as follows: Field Description dwName Specifies the cue point name. This value must match one of the names listed in the <cue-ck> cue-point table. dwLength Specifies the length of the section in samples. dwLoops Specifies the number of times to play the section. Associated Data Chunk The <assoc-data-list> associated data list provides the ability to attach information like labels to sections of the waveform data stream. The <assoc-data-list> is defined as follows: <assoc-data-list> -> LIST('adtl' <labl-ck> // Label <note-ck> // Note <ltxt-ck> // Text with data length <file-ck> ) // Media file <labl-ck> -> labl(<dwName:DWORD> <data:ZSTR> ) <note-ck> -> note(<dwName:DWORD> <data:ZSTR> ) <ltxt-ck> -> ltxt(<dwName:DWORD> <dwSampleLength:DWORD> <dwPurpose:DWORD> <wCountry:WORD> <wLanguage:WORD> <wDialect:WORD> <wCodePage:WORD> <data:BYTE>... ) <file-ck> -> file(<dwName:DWORD> <dwMedType:DWORD> <fileData:BYTE>...) Label and Note Information The `labl' and `note' chunks have similar fields. The `labl' chunk contains a label, or title, to associate with a cue point. The `note' chunk contains comment text for a cue point. The fields are as follows: Field Description dwName Specifies the cue point name. This value must match one of the names listed in the <cue-ck> cue-point table. data Specifies a NULL-terminated string containing a text label (for the `labl' chunk) or comment text (for the `note' chunk). Text with Data Length Information The `ltxt'' chunk contains text that is associated with a data segment of specific length. The chunk fields are as follows: Field Description dwName Specifies the cue point name. This value must match one of the names listed in the <cue-ck> cue-point table. dwSampleLength Specifies the number of samples in the segment of waveform data. dwPurpose Specifies the type or purpose of the text. For example, dwPurpose can specify a FOURCC code like `scrp' for script text or `capt' for close- caption text. wCountry Specifies the country code for the text. See ``Country Codes'' in Chapter 2, ``Resource Interchange File Format,'' for a current list of country codes. wLanguage, Specify the language and dialect codes wDialect for the text. See ``Language and Dialect Codes'' in Chapter 2, ``Resource Interchange File Format,'' for a current list of language and dialect codes. wCodePage Specifies the code page for the text. Embedded File Information The `file' chunk contains information described in other file formats (for example, an `RDIB' file or an ASCII text file). The chunk fields are as follows: Field Description dwName Specifies the cue point name. This value must match one of the names listed in the <cue-ck> cue-point table. dwMedType Specifies the file type contained in the fileData field. If the fileData section contains a RIFF form, the dwMedType field is the same as the RIFF form type for the file. This field can contain a zero value. fileData Contains the media file.